A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
On this page below you can locate more sensible advice related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily available, the job can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and position the new bathtub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to change the arrangement of your previous water pipelines.
Your tools and material list must make up the following:
Planning for the Setup
First of all, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic as a result of the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, put the tub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level checks out degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will resolve it into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that write-up about A Step-by-Step Guide to Installing a Bathtub through an associate on another web blog. Do you know about someone else who is looking into the subject? Please feel free to promote it. Kudos for your time. Visit us again soon.
Check This Out
Report this page